Lighting Systems — An Introduction to ANSI C137.1

February 6, 2017

Roy Harvey

The recently formed ANSI C137 Lighting Systems Committee created a working group to develop a standard for a zero-to-10 volt analog interface between dimmable LED drivers, fluorescent ballasts and dimming controls. At present, there is no widely accepted industry standard for analog dimming of LED sources. The new standard, C137.1, will enhance interoperability of drivers and dimming controls and improve the uniformity of output of multiple drivers operating on the same control circuit.

Photo credit: Osram Sylvania

The standard is based on the 0-10 V fluorescent dimming interface specified in ANSI C82.11 Annex A, which is similar to the interface specified in IEC 60929 Annex E. C137.1 adds several new features and specifies the interface in more detail.

The main new feature is a standby or “electronic off” mode. This optional mode disables the driver’s output power while its control circuitry remains awake. This feature can eliminate a relay used to disconnect the driver’s output and an extra pair of wires to control the relay. Standby mode is entered when the control signal drops below about 0.5 V. C137.1 also adds specifications for dynamic response, the time to start up or change from one level to another.

However, the standard covers more than drivers and ballasts; it also has requirements for dimming controls and system wiring. Like C82.11, C137.1 specifies that the driver or ballast supply current that the control unit sinks and uses to generate the control voltage. C137.1 requires that the control unit manufacturer declare how much current the control unit can sink. This gives a lighting system designer information needed to help ensure that the control unit can handle the current sourced by the driver(s) connected to it. C137.1 also specifies that multiple controls, such as a wall dimmer and a daylight sensor, can connect to the same control wires without damaging each other.

Finally, C137.1 requires that the voltage drop caused by control wiring resistance be no more than 0.3 V. This helps ensure adequate noise margin and uniform operation (light levels) of many drivers sharing control wires. Requirements on tolerances for the endpoints of the dimming range further contribute to uniform operation.

The working group has been developing the standard since February 2015. A draft is being prepared for public review according to the ANSI process. The standard is expected to be published in early 2017, but some of the above information may change, so it is best to check the published edition.

If you have questions regarding these new regulatory requirements or need immediate testing to ensure that your products are in compliance, please contact UL to discuss testing, advisory or training needs at PerformanceLighting@ul.com.


Roy Harvey is SSL Electronics & Infrastructure Standards Manager at Osram Sylvania. He is also Vice-chair of ASC C137 and Head of C137.1 Ad Hoc Group.

 

Related Articles


Changing Scene

  • Contact Delage Announces New Partnership with Zilux

    Contact Delage: New Representation Agreement – Zilux

    Contact Delage is pleased to announce a new partnership with Zilux for the representation of their products in the regions of Montreal, Laval, Estrie, Lanaudière, Laurentides, and Montérégie. Specializing in the design of aluminum lighting and urban furniture, Zilux, a Quebec-based manufacturer, combines innovation and durability to enhance your outdoor design projects. Their expertise in… Read More…

  • Mac’s II Agencies Announces Jamie Capell as the New Sales Manager for Lighting Specification

    Expanding Expertise: Mac’s II Agencies Strengthens Lighting Division

    Mac’s II Agencies is pleased to announce the expansion of its lighting division with the addition of Jamie Capell as the Sales Manager for Lighting Specification. Jamie brings 25 years of experience in the lighting and electrical industry, most notably serving as the Director of Sales for a local lighting agency in British Columbia. With… Read More…


Design

  • Light ARchitect Is Revolutionizing Lighting Design for Architects & Designers

    Light ARchitect Is Revolutionizing Lighting Design for Architects & Designers

    Traditionally, lighting design could be a tedious process, often involving physical mockups, time-consuming calculations, and static renderings using multiple software tools. With advancing technology, these traditional methods are giving way to more sophisticated tools that enhance precision, speed, and visualization. On the downside, many of the new tools are not particularly intuitive and the learning… Read More…

  • Project Story: Sainte-Thérèse High School Outdoor Lighting Upgrade

    Project Story: Sainte-Thérèse High School Outdoor Lighting Upgrade

    August 6, 2024 Built in 1980, the building that houses Sainte-Thérèse high school, in Quebec Canada, was looking a little worse for the wear. Renovation work began with two major projects: introducing a multidisciplinary sports centre, as well as redesigning the parking lots.  The employee and visitor parking lots were completely reconfigured during phase 1… Read More…


New Products

  • Magic Lite: New 5-Channel High-Performance LED Amplifier

    Magic Lite: New 5-Channel High-Performance LED Amplifier

    Designed for professional-grade LED systems, the 5-Channel High-Performance Amplifier delivers precision, scalability, and reliability. Using advanced MOSFET technology and high-speed 10Mbps optical couplers, this amplifier ensures robust power output and flawless signal transmission across large-scale, synchronized LED applications. Whether expanding capacity for PWM controllers or enhancing system stability, this amplifier simplifies complex lighting designs while… Read More…

  • Eureka: Lattice – 3D Printed Ceiling Suspended Fixture

    Eureka: Lattice – 3D Printed Ceiling Suspended Fixture

    Lattice is a one-of-a-kind 3D metal printed fixture. Layer upon layer of intricately braided aluminum branches meld into one of three comprehensive shapes. The result is a stunning glowing light fixture that will add a luxurious feel to ambient environments. EXCLUSIVELY AVAILABLE ON DEMAND. Read More…